Skate Cake Recipes

SKATE CAKE

Steps:

• Heat oven to 350°F (325°F for dark or nonstick pan). Make and bake cake as directed on box for 13x9-inch pan. Cool 10 minutes. Run knife around side of pan to loosen cake; remove from pan to cooling rack. Cool completely, about 1 hour. For easier handling, refrigerate or freeze 30 to 60 minutes or until firm.
• Cut cake as shown in diagram. Tint 1/3 cup of the frosting with 3 drops green food color. Arrange pieces on foil-covered tray to form skate as shown in diagram, trimming pieces to fit. Attach pieces of cake with frosting. Frost with a thin layer of frosting to seal in crumbs. Refrigerate or freeze 30 to 60 minutes to set frosting. Frost entire cake.
• Outline inner throat and tongue of skate with toothpick. Tint 2 tablespoons white frosting with 2 drops yellow food color; frost inner throat. Frost tongue and back of throat with green frosting. Use fruit snack to form brake, strap and back of throat. Make 4 slits in bottom edge of blade, and insert cookies for wheels. Outline skate and blade with decorating gel. Use ring candies for eyelets and wheel axles. Cut 1/4-inch-wide strips of fruit snack and use for laces. Store loosely covered.

BAKED SKATE

Steps:

• Preheat the oven to 350 degrees F (175 degrees C). Lightly grease a baking dish.
• Finely grate the zest from 1/2 of the lemon. Cut lemon in half, remove seeds, and juice it into a small bowl. Mix bread crumbs with melted butter in another small bowl.
• Rinse skate wings and pat dry. Cut into 4 pieces and place in the prepared baking dish. Season with salt and pepper, sprinkle with lemon zest, and pour lemon juice over top. Sprinkle with dill and then bread crumb mixture.
• Bake in the preheated oven for 15 minutes. Continue to bake, checking in short increments, until fish is uniformly white throughout and can be easily lifted from the skeleton, up to 5 more minutes; do not overcook.
• Carefully move to a serving platter and garnish with lemon slices and dill sprigs.

SKATEBOARD CAKE

Steps:

• Prepare cake batter as directed on package; pour into one 9-inch round cake pan and one 13x9-inch baking pan, making sure that the level of batter in each pan is the same. Bake as directed on package for each pan size. Cool in pans 5 min.; remove to wire racks. Cool completely.
• Spread tops of 4 of the vanilla creme-filled chocolate sandwich cookies with some of the icing; top each with second vanilla creme-filled chocolate sandwich cookie to resemble a skateboard wheel. (You will have a total of four "wheels.") Attach one set of cookie wheels to each end of the wafer cookies with the remaining icing; set aside.
• Place rectangular cake on large board or platter. Cut round cake crosswise in half; position one half at each short side of rectangular cake, with cut side of round cake against side of larger cake as shown in diagram to resemble a skateboard.
• Tint whipped topping with food coloring to desired color; spread onto tops and sides of cakes. Sprinkle a few drops of food coloring randomly over top of cake; carefully cut through food coloring with palette knife or spatula for marble effect. Decorate with chocolate pieces as desired. Use gel to write desired message on cake. Store in refrigerator. Arrange wheels on top of cake just before serving.

ICE-SKATE COOKIES

Steps:

• Position a rack in the center of the oven and preheat the oven to 350 degrees F. Line a baking sheet with parchment paper.
• Dust a work surface with a light coating of flour and roll out the dough to a thickness of about 1/4 inch. Use an ice-skate cookie cutter to cut out cookies. Use an offset spatula to carefully transfer cookies to the prepared baking sheet, leaving about 1 inch of space between each cookie.
• Bake until the cookies are golden brown round the edges, about 10 minutes. Let cool for a few minutes on the cookie sheet to firm up, then transfer to a cooling rack to cool completely.
• Meanwhile, fill a piping bag with a #4 tip with the white icing, a piping bag with a #2 tip with the black icing, a piping bag with a #2 with the gray icing, and a piping bag with a #1 tip with the blue icing.
• Start with the white royal icing bag; this icing will double as your outline and flooding icing. On a cooled cookie, outline where the tongue of the ice skate will be, bringing the line down to the top of the tip of the shoe. Fill it in and even out the shape using a toothpick. Repeat with the remaining cookies.
• Next use the black royal icing bag; this will also double as your outline and flooding icing. Pipe a thin sole on a skate and then pipe a heel; flood and use a toothpick to make everything even. Repeat with the remaining cookies.
• Use the gray icing to outline the blade of a skate. Use a toothpick to get the sharper points and straight lines. Repeat with the remaining cookies.
• Outline the rest of the skate boot with the white royal icing and flood the outline. Use your toothpick to smooth out the icing and eliminate any air bubbles. Repeat with the remaining cookies.
• Immediately use your gray icing to pipe 6 evenly spaced lace holes on a cookie. Starting at the cookie edge, use the blue icing to make lace strands: Above the 6 lace holes, make two sets of two laces that connect evenly with the previous lace holes. (They will make a > sign). Repeat with the remaining cookies. Let cookies dry for about 15 minutes.
• Mix the pearl dust with enough grain alcohol to make a thin paste. Use a paintbrush to paint the paste onto the blade of a skate. Use the same pearl dust on a dry paintbrush to highlight the boot of the cookie by lightly brushing it with pearl dust. Repeat on the remaining cookies. Allow cookies to dry for about an hour before serving.