French Bread In Bread Machine Recipe 435

THE BEST FRENCH BREAD (BREAD MACHINE)

Steps:

• Add 3/4 cup water, salt, flour, parmesan cheese, garlic powder and yeast to bread machine pan in order suggested by manufacturer.
• Select dough/manual cycle.
• When cycle is complete, remove dough from machine to a lightly floured surface.
• Roll dough into a 15x10 inch rectangle.
• Beginning at long end, roll up tightly as for jelly roll.
• Pinch seams and ends to seal.
• Taper ends by gently rolling back and forth.
• Place loaf, seam side down on a greased baking sheet sprinkled with cornmeal.
• Lightly brush loaf with oil.
• Cover and let rise in warm draft-free place until almost double in size, 10 to 15 minutes.
• With a sharp knife, make 3 or 4 diagonal cuts about 1/4 inch deep across the top of loaf.
• Lightly beat egg white and 1 tablespoon water; brush some of egg white mixture over top of loaf.
• Bake at 375 for 20 minutes.
• Brush again with remaining egg white mixture and sprinkle with sesame seeds.
• Bake 5 to 10 minutes more or until done- bread should sound hollow when tapped.
• Remove the bread from the baking sheet and cool on a wire rack.

FRENCH BREAD | BREAD MACHINE

Steps:

• Add all the ingredients (water, salt, bread flour, yeast) in the order recommended by your bread machine manufacturer.
• Close the lid, select the "French bread" cycle, 1.5 lb loaf size and crust of your preference (dark is preferred for French bread) and start the cycle.
• French bread is ready once the cycle is complete.
• Remove the container from the bread machine. Invert and shake it a little bit to remove the bread.
• Place it on a cooling rack to cool it down.
• Once cooled down, slice it with an electric knife or a serrated knife.
• Remove the dough from the bread machine pan just after the last knead cycle and knead it on a lightly floured surface.
• Shape the dough into a loaf and apply a few cuts using a serrated knife and allow to rise for 60 minutes in a warm place.
• Bake in the preheated oven at 400 °F for 30 minutes.
• Remove from oven and allow to cool on cooling rack. Slice it wit a serrated or electric knife.

BREAD MACHINE FRENCH BREAD (SIMPLE, SIMPLE, SIMPLE)

Steps:

• put in machine in order and push buttons to make a 1.5 Lb french loaf.

BREAD MACHINE CRUSTY FRENCH BREAD

Steps:

• Gather the ingredients.
• Add the room temperature water, oil, dry milk, all-purpose flour, bread flour, sugar, salt, and yeast to the bread machine according to your manufacturer's preferred order.
• Use the French bread setting on your machine but remove the dough after the last kneading cycle before the baking cycle begins. Or use the dough cycle, punch down the dough to let air escape, let it rise again (45 minutes to 1 hour), knead lightly, and let it rise again (another 45 minutes to 1 hour) before forming into loaves.
• Spray or lightly oil a large cookie sheet and sprinkle with the cornmeal.
• To form the loaves, transfer the dough (it will be soft) to a lightly floured board. Sprinkle with a little all-purpose flour.
• Cut the dough into 2 portions and roll each portion into a rectangle about 12 to 15 inches wide (add more flour as needed).
• Starting at the long end, roll up the dough, pinching the seams well. Repeat with the next roll.
• Place the loaves on the prepared cookie sheet; cover with a clean dishtowel and let rise another hour.
• While the loaves are rising, preheat the oven to 400 F. Place a pie plate on the lower rack of the oven and add about 1 inch of boiling water. Place the pan with the dough on the middle rack and bake the bread for 15 minutes.
• Lower the heat to 350 F and bake for another 25 minutes until golden brown.
• About 5 minutes before the loaves are done, mix the egg white with the cold water in a small bowl and brush the loaves with the egg wash .
• Once baked, remove from the oven and let cool.
• Serve and enjoy.

FAILPROOF FRENCH BREAD (BREAD MACHINE)

Steps:

• Place ingredients in bread machine according to manufacturers directions.
• Start machine on dough setting.
• When dough cycle is complete, remove dough with floured hands and cut in half on floured surface.
• Take each half of dough and roll to make a loaf about 12 inches long in the shape of French bread.
• Place on greased baking sheet and cover with a towel.
• Let rise until doubled, about 1 hour.
• Preheat oven to 450°.
• Bake for 15 to 20 minutes or until golden brown, turning pan around once halfway during baking.
• Remove baked loaves to wire racks to cool.

BREAD MACHINE FRENCH STYLE BREAD

Steps:

• Measure ingredients into baking pan in order listed.
• Black& Decker Setting 6 (Specialty- French 3H 30M cycle).

BASIC MACHINE FRENCH BREAD

Steps:

• Add to the bread pan in the order yours needs.
• For mine it is water first.
• Then I add half the flour and the salt followed by the rest of the flour and the yeast on top.
• This will run well on the normal, rapid, and delay start cycles.

WHITE BREAD FOR THE BREAD MACHINE

Steps:

• Place water, sugar, salt, oil, bread flour and yeast into pan of bread machine.
• Bake on White Bread setting. Cool on wire racks before slicing.